If your Washing Machine won’t Start, here’s how to Fix It

If you are like most individuals, the time you allot to family chores is restricted. Just imagine making an attempt to throw a load of laundry in earlier than heading off to work and finding that your washing machine will not begin-major frustration, right?

As a substitute of expecting the worst case state of affairs of spending a whole bunch of dollars for a brand new machine, you might first attempt your hand at a DIY washing machine repair. There are a number of common issues you’ll be able to verify to diagnose and resolve the problem on your own.

We’ve created a step-by-step guide on how to determine what’s incorrect and methods to repair a washing machine that will not begin. You may only need a few easy tools and you’ll be on your manner to scrub clothes in no time.

Before you begin, you may need the following family instruments:

– Screwdrivers (Phillips and flat-head)

– Hex head and torx wrenches

– Rubber mallet

– Pliers

– Nut drivers, socket set and adjustable wrench

– Multimeter electrical tester

This may appear too simple a solution to even consider, but it’s more common than you think. Washing machines usually vibrate and move in the course of the spin cycle, so the cord can come free. Make sure the machine is tightly plugged in.

Subsequent, test for a tripped circuit breaker. If neither is at fault, you will have a damaged power cord. If there is not any energy running by the cord, you’ll have to exchange it. Reset the breaker and check out to start the washer. Check the continuity with a multimeter.

Lid Switch or Fuse

High-load washing machines use a lid change as a safety feature to solely function when the door is properly closed. A damaging test signifies the change will should be changed. If the door is closed, you will must verify the switch continuity along with your multimeter.

Your machine could have a special fuse located inside the control panel. A blown fuse might be black in coloration and must be changed. Unplug the washer, then remove the couple screws on the dashboard to entry the panel.

Front-load washing machines use a door switch, lock and strike that have to be engaged earlier than the washer will begin. Inspect the door switch in the door frame and ensure the lock engages with the strike.

Disconnect the facility and take away the front panel to check the change continuity, and exchange it if wanted.

Begin Swap and Timer

Normal put on could cause the start swap within the timer to slide on the shaft. Remove the power supply to visually examine the back of the timer. The knob should interact the shaft when pushed in and out.

Additionally, although it’s much less frequent, the timer itself could also be defective. Examine the continuity and replace it if needed.

Overheating

If you have had a heavy wash day where you’ve got run several hundreds in a row without problem however then your machine will not start again, you might have overheated it. Simply permit your washer to cool down for a couple hours before attempting to start it again.

Principal Management Board

On electronically controlled fashions, the principle management board does simply as its title suggests-it controls the principle parts of the equipment. If the control board malfunctions, it could not provide the correct voltage to the door lock, drive motor or fill valve which will prohibit it from beginning.

You may unplug the washer and visually examine the back of the control board for burned or damaged components. Nonetheless, except you are very aware of how to put in a brand new management board, you need to depart this to a professional restore service.

Look to Puls for All of your Washing Machine Repairs

You never need to go it alone when trying to restore a washing machine that won’t start. Puls’s qualified technicians are able to carry out an in-house inspection, even on the identical day if wanted, to supply an accurate analysis, and repair your machine quick.

Whether the repair is simply too tough in your skill level or you’re just short on time, a low $79 inspection payment will have you one step closer to scrub clothes. Better yet-this charge is waived if you carry out the really useful repair with Puls.

We take all of the fear out of restore work with our 90-day restore assure on all components and labor. If the rest goes unsuitable, we’ll be back to repair it without cost.

Want to save lots of much more? Get 5% off your first service while you subscribe to Puls.

We’re here to make washing machine restore easy. Take a number of seconds online now to e book your appointment, and your washing machine will likely be operating like new very quickly.